How to Remove Automobile Stickers

May 26th, 2016

There are many who like to express themselves through their cars. It is very easy to find bumper stickers or window art on cars and other automobiles. Although they make your car look more appealing, doing away with such bumper stickers when necessary can be a nasty job. Many a times, the sticker is removed but it leaves behind the residue to make it look worse. But no worries, if it’s your first attempt at removing a sticker from your car, here are a few simple ways to remove the sticker.custom NHL decals stickers

1. Pre-soak. Pre-soaking is an easy method to remove stubborn stickers. Use soapy water to remove the sticky paper. Use a spray of soapy or alcoholic solution and spray it generously over the sticker. Or soak the sticker in the soapy water for some time and then try removing it as much as you can. If it still doesn’t work, use natural agents.

2. Use natural agents. Dip a cloth in vinegar. Place it on the sticker and let it soak for about 5 minutes. Reapply as and when required. Then, peel it off starting from the edges. If it still leaves away sticky residue, rub vinegar over the area. You could also follow the same procedure using a mixture of eucalyptus oil, soapy water, and alcohol solution.

3. Use a Blow dryer. Another interesting way to remove the sticker is to heat the surface using a blow dryer. Make sure you hold it at least 6 inches (15.2 cm) away from the desired area. Start peeling off the sticker from the corners while you go on applying heat.custom mlb stickers

4. Use WD-40. Wet a cloth using WD-40 or a lighter fluid and rub the cloth on the sticker. Use a spatula or an old CD or credit card to start peeling off the edges. This will make it come off easily.

Warnings

  • WD-40 can mess up the paint if rubbed for a longer time. Work on smaller patches at a time.
  • While using a blow dryer, avoid excess heat or the paint would start chipping off slowly.
  • Do not use a razor or sandpaper. It would take off the sticker quickly but it might damage the paint.

How to Embroider

April 27th, 2016

The art of sewing fancy stitches in fabric to create designs and pictures is as varied and fun today as it has been for centuries. You too can get started on your own journey into the world of thread and needle. Keep reading for detailed instructions.

1. Obtain fabric, an embroidery hoop, an embroidery needle (largish eye for your heavier thread) and some embroidery floss or yarn. A loose weavable fabric is a good choice for your first projects.

2. Stretch your fabric taut using the embroidery hoop. An unstretched fabric will wrinkle and become difficult to work with as you snug down the stitches.

3. Cut your floss, yarn, or heavy thread to a length of approximately 25 inches (63.5 cm). This is long enough to make some nice stitches and short enough so that it will not tangle easily.

4. Thread your needle.

5. Tie a knot in the end of the thread/floss/yarn.

6. Poke the needle through the fabric from the back side. From here on out, it’s a matter of placing stitches where you want them so that they form an outline or shape that is pleasing to you.

There are different types of stitches.

Method 1. Types of Stitches
  • Running Stitch – The classic "sewing" stitch… up,down,up,down… evenly spaced in a line so that the line looks like a row of dashes —–
  • Back Stitch – Backstitch
  • Blanket Stitch – Sew Blanket Stitch
  • Slip Stitch – Slip Stitch
  • Blind Stitch – Same as Slip Stitch
  • Satin Stitch – Satin Stitch
  • Split Satin Stitch – as Satin Stitch but the second layer of stitches are sewn into the previous row splitting the thread of the stitch.
  • Feather Stitch – Looks like someone walking in long skis. The tracks X over each other.
  • French Knot – Come up from the back. Twist the thread around the needle. Poke the needle back down through the fabric right beside where it came up. The knot should tie as the thread gets pulled to the back side of the piece again.
  • Lazy Daisy – Up from the back. Make a loop on the front by poking the needle back down beside where it came up and leaving the thread loose. Come up from behind again and "tack" the end of the loop down with a tiny stitch. Repeat for each petal. of your daisy.
Method 2. Alternatives

Check out Cross Stitch embroidery. This type of embroidery use the cross stitch only and is good for beginners. Counted Cross Stitch is a variation you can look into if you enjoy cross stitching.*Look at Long Stitch embroidery. In this type of needlecraft, multiple long straight, downward stitches are used to build up an image or pattern

Tips

  • Purchasing a small embroidery kit can be a good introduction. It saves you the trouble of designing, choosing colors, and choosing a yarn.
  • Start with something small that can be completed quickly for your first project.

How to Decorate a Kitchen

April 22nd, 2016

The kitchen is one of the most important rooms in a house; it is where meals are cooked and where family converge and hang out. There are many ways to add decorations to a kitchen and make it inviting and warm. Here are some tips on how to decorate yours!NBA wall decals

Method 1. Making Small Changes

1. Declutter. If you are like many people, you may be guilty of too many details. Take an honest look at your kitchen. Is it too cluttered? You can easily sidestep this problem by taking a few things away or simply rearranging your storage system to keep the extras from view. A new kitchen may emerge just from this one step.

  • If you have no choice but to display all of your appliances and dishware for a lack of storage, you’re going to have to get some! Buy a cart, bring an extra piece in, or invest in some attractive bins and containers.

2. Use color to make it cozy. If you stick to whites like a piece of rice, you risk ending with a kitchen that seems hospital-like and cold. Add a few accent colors that are bright and cheery to make it seem warm, lived in, and loved.

  • Choose certain spots for your color. The seating? The lighting? An area of the countertop? In addition, do not feel pressure to stick to just one — different hues of the same color work well together — and remove the pressure to find the exact right tone.

3. Add fresh flowers. Plants and flowers add lively decoration to any room and are good for the environment. Add a functional decoration to your kitchen by creating a window box with fresh herbs, or replace fresh-cut flowers in a kitchen table vase every few days to keep it looking new.NBA wall decals

  • Make sure they match your theme! A simplistic, neutral kitchen would benefit nicely from a simple Easter Lily or two while a kitchen with more pizzazz might look better with a bunch of carnations or daisies. What flower fits your kitchen’s personality?
  • Herbs are not grown in factories, you know. To kill two birds with one stone, grow them yourself in your kitchen window! What a cute little way to spruce up your kitchen and jazz up your meals.

4. Jazz up your fridge magnets. For those of us that don’t have a massive budget to install gold-flecked countertops lined with rubies, a fun way to spruce up your kitchen’s ambiance is to spice up your fridge! There are loads of fun choices available that you can cater specifically to your personality.custom NHL decals stickers

  • Sometimes it’s the little things in life. Buy a whole bunch of magnetic letters and leave your roommate a nice message about how you drank the last diet Coke, or even put magnets on the back of photos from favorite vacations. If it sticks, it’s a possibility.

5. Use texture to your advantage. When you have one look going on in your kitchen (probably smooth and flat), it can look one-dimensional and blah. To add an extra zing to your cooking space, work in texture, too.

  • Go for textured containers, textured linens, and textured wall hangings or curtains. A little bit here and there will go a long away against the smoothness of the countertops, the table, and the cabinets.

6. Add unexpected pieces of furniture. Long gone are the days when the kitchen was just the kitchen. Now, the living room is the dining room, the kitchen is the common area, and the dining room could even be for show. While you don’t have to embrace the lifestyle, consider jazzing up your kitchen with no-exactly-meant-for-the-kitchen pieces.

  • A china cabinet, armoire, or credenza is a good way to start expanding the look of your kitchen. If you have a great piece, make it the focal point. Voila, instant theme! Add bookshelves, a bench, or other multi-purpose pieces to seal the deal. After all, this is your kitchen.

7. Change the linens. One way to give the whole room a cohesive theme is to choose one pattern for your curtains, tablecloth, and hand towels and create a matching set of linens. The only hard part of this is committing to just one!

8. Switch décor seasonally. Give your kitchen a celebratory feel by changing out linens, curtains, or dishes for special holidays. Rotate these items, which all complement the personality of your kitchen, with the changing seasons to add seasonal colors and elements.

  • This has one extra (albeit teeny) benefit: with the seasons, you can give it a good cleaning. Kitchens are the rooms that get dirtiest, and if you schedule four annual overhauls, your appliances, dishware, and linens will stay good as new.
Method 2. Making Big Changes

1. Create shelving. Since your cabinets are probably stocked to the brim, you’ll probably need other methods to house what’s left over (the decorative doodads and the like). For this, you have two options:

  • Floating shelves. If you have walls (and you probably do), you can install floating shelves with ease. They will also draw the eye upward, so if your kitchen is small, it will distract from the cramped-ness of the rest of the room.
  • Cubed shelving. This is turning a wall into a series of boxes. They are artistic and utilitarian. For an added touch, decorate each box (or some of the boxes) with different types of shelf paper. Tada, kitchen innovation.

2. Stick with an accent color. A kitchen does not need too much going on, so sticking to black and white and other neutral tones are your best bet. Nevertheless, take that monochrome look and spice it up with a specific accent color. Maybe bright yellow or bright blue? Suddenly, the eyes aren’t concerned with the size and immediately focus on your great pieces.

  • Think of accents in your art, towels, and dishware. But remember: it’s an accent color. Too much of an accent color makes it an accent color no more. If you overdo it, you’ll lose the effect. Stick to 4 or 5 pieces.
  • Three words: Paint. The. Ceiling.

3. Consider losing all your doors. Whether it’s cabinets or drawers, think about removing the doors. Sure, this means everything on the inside will need to be organized, but that can easily be overcome with cute storage containers and pretty glass and textured bins. And more opportunities to show off your decorating side!

  • The idea here is that you’re opening everything up — literally. The more open it is, the more room the eye will see. The more room the eye sees, the larger the room will seem.

4. Use mirrors. Just because you’re in a kitchen doesn’t mean you can’t do whatever the heck you want. And since you probably know that mirrors open rooms, why not put one in your kitchen?! It doesn’t have to scream "I’m a mirror!" either — simply place it underneath your cabinetry for a is-it-there-is-it-not-there look.

  • Mirrors (with frames) also make for good trays. Slap some felt on the back and boom — automatic DIY success.

5. Paint the walls or cabinets. A room’s color helps it feel warm or relaxing, so decorate your kitchen by adding a fresh coat of paint to the walls or cabinets. White is a popular choice, but you can opt for a light shade of blue or yellow if an all-white room isn’t appealing.

  • Use a variety of neutral tones. While using white, cream, and gray may seem drab, when you mix up various neutral tones, it adds depth and sophistication, while staying classic and simple. Turn boring into brilliant by just using a few shades.
  • Add a focus. Paint three walls one color, and the fourth wall a color that pops. The eye will move to it without even realizing it. If you have a great window or area of the room that’s eye-catching, amp it up with a focus color.

6. Add a backsplash. If you are committed to white walls (either against your will or not), you may feel like your kitchen is a little lacking. Get around this by adding a backsplash — that is a panel behind the sink or stove that protects the wall from splashes. And the panel can be any style you like!

  • It’s easiest to stick to a solid color to add an accent, but consider tiles and patterns, too. Tiles can add extra texture to an otherwise smooth wall.
  • If you already have tile, think about buying tile stickers. A super (couldn’t be easier) easy way to jazz up that backsplash in seconds.

7. Play around with lighting. You have more options here than you probably realize. Depending on your electrical system, lighting can take on several different sources. Each one can vamp up your kitchen, rejuvenating it with life.

  • Play around with table lamps. Those work on counters, too! It adds a homey, unexpected feel to any area. If you are feeling extra creative, make a "lamp" out of a string of Christmas lights in a clear, glass jar.
  • Put lights in (and under) your cabinets. Not only will your pieces be lit up (and they’ll look fantastic), it can serve as dim lighting when the full guns aren’t necessary. In other words, romantic and functional.
  • Get a great hanging lamp. Even if you don’t have much space, a great hanging lamp with an eccentric drum shade can be so much fun you won’t notice anything else. Or get several small ones for more lighting options.
  • Go for sconces. If you don’t have room for a big hanging shade or lamps on your countertops, a sconce is an easy way to go. Some are incredibly easy to attach and can provide much more light than their size would allow.

8. Focus on one element at a time. Decorating a kitchen can become overwhelming if you try to change everything at once. Give yourself one decorating project, like painting or buying new dishes, and stay with that project until it’s completed. You can move on to others later if you feel your kitchen needs more decorating.

  • This well help you know when to stop and when (and how) to keep going. Sometimes adding a focal point or changing your dishware can put a new twist on your kitchen that may be the small tweak that it needed. Create a priority list of things you want to add/change and slowly move down it as necessary.
Method 3. Choosing a Theme

1. Pick a style for your entire kitchen. The main way most people go wrong with their kitchens is in not choosing a theme. They have a vision here and a vision there (or they pick up knickknacks as they find them) and conflate them together into one hodgepodge of a kitchen. Pick a theme and you’ve tackled 80% of the battle.

  • It’s important that your kitchen decorating be cohesive and make the room look pulled together. Accomplish this by deciding on one theme for your kitchen and choosing decorations that match it. Some home improvement stores have entire sets of kitchen decorations based on themes like country living, French or art deco styles.

2. Go ultra-modern. If you love sleek, shiny things, a super modern kitchen may be your style. Think in harsh angles and blacks, whites, and popping, bright colors. Most metallic, stainless steel, and geometric art pieces would adorn this kitchen. Glass, too!

3. Do a sea theme. A common (but still classy) theme to choose is a sea theme. Whether you live on the ocean or want to bring the ocean to you, this theme is cozy and inviting.

  • Line your shelves with seashells, sailor’s gear, and scenes from the beach. Work in elements of tan, cream, and blues. What a great excuse to make a DIY project with rope, netting, and items from the beach!

4. Opt for an earthy theme. If you are fond of dark, warm colors, an earthy, natural, woodsy theme may be more up your alley. Think of dark cabinets, wooden dishware, bowls of potpourri, cherry reds, rich mahoganies, and dark oranges.

5. Go for a colored theme. If an outright themed design is too much for your sensibilities, just go for a color. Hues can line up a kitchen, too! Blue stools, blue dishes, blue cabinet pulls — everything will be brought together regardless of your items’ designs. Just make sure you don’t get sick of it!

  • This theme is a bit dangerous. Too much of one tone can be overkill. However, if you do not have the authority to revamp your kitchen (if renting), incorporating color as your theme may be the best way to go.

Tips

  • Remember that any new decorations should still allow your kitchen to be practical and functional. Avoid any large decorative items that will take up space on your counter tops or stove. Opt for wall hangings and hanging decorations that will be out of your way.

How to Decorate Your Notebook

April 7th, 2016

You don’t have to spend a lot of money to have a beautiful notebook that will have everyone asking, "Where did you get that?" To decorate your own notebook, all you need is a few basic craft materials, some time, and the willingness to flex your creativity muscle. If you want to know how to decorate your notebook and have your friends and classmates wish they could have done the same, just follow these simple steps.

Method 1. Pictures and Stickers custom NHL decals stickers

1. Write your name on a piece of paper.custom images printing Choose a paper that is shaped like a small rectangle that fits the size of your notebook, and reinforce it with cardboard for durability. You can write not only your name, but the subject of your class, and your roll number, or any other relevant information. Once you’ve filled out the card, you can glue the paper to the front of the notebook — ordinary glue or a glue-stick will do. Also use sticky notes for easy notebook organisation. Just write the subject and stick the sticky note on the side of the book. Do this to all your books. Now it looks so much more organised and fancier!

  • After you glue down the paper, smooth it down to avoid any bumps. If it’s too bumpy, then react quickly and take the paper off before it sticks down properly and re-glue it.

 

2. Glue fun pictures to the cover of your notebook. You can use pictures of animals, pictures from comic strips, or even pictures of your favorite celebrities. You can cover as much of the notebook as you like, as long as you don’t cover the card with your name on it. This is all about personalizing the notebook — choose the pictures that appeal to you.

3. Add stickers to the front of your notebook. Place the stickers in any empty parts of your notebook. You can also partially cover the pictures you’ve glued onto the notebook, if you like, for a layered effect. 3D stickers also make it look really awesome-but don’t use them if you don’t want to. Just don’t cover the index card with the stickers. You can also make your own stickers and put them on your notebook.

4. Glue fabric around the index card. Find a lacy, beautiful fabric and and glue it around the border of the index card. This will give your notebook a more elegant look. Some stronger glue will be best for this purpose, such as craft bond tacky glue, or craft bond fabric and paper glue. You can even decorate the fabric with glitter.

5. Doodle around any free spaces in your notebook. If you haven’t covered your notebook completely, you can use the same color marker you used for the index card to draw small designs on the notebook, such as hearts, stars, lips, or flowers. And if you get bored with your new notebook, you can always add more layers to it.

Method 2. Glitter Stripes

    1. Brush one 2" (5 cm) horizontal stripe of Mod Podge onto your notebook. This type of glue and sealer is perfect for securing glitter to your notebook. To cover your notebook in glittered horizontal stripes, you’ll need to brush on the Mod Podge for one stripe, cover it with your desired color, and then do the process again for another color. If you brush all of it on at once, the glitter won’t stay within the confines of the stripes and will spill everywhere. Use a sponge brush to apply the Mod Podge.

    You can adjust the size of the stripe to the size of your notebook. You should have at least five stripes on the notebook, so you can make them a bit thicker or thinner so they cover the notebook evenly.

    2. Cover this stripe with one color of glitter. Choose one color of glitter and sprinkle it on to the stripe. You can smooth down the glitter with your fingers, and shake off any excess glitter. For best results, wait a minute or two for this layer to dry.

    3. Brush another 2" (5 cm) horizontal stripe of Mod Podge underneath the first stripe. Once you’ve created the first glittery stripe, make another stripe of glue below it.

    4. Cover this stripe with a different color of glitter. Do exactly what you did with the first color of glitter, except use a new color that will nicely contrast with the first. For example, you can use blue and yellow, green and red, or silver and gold.

    5. Repeat these steps until you’ve covered the notebook with glitter. Continue adding a stripe of Mod Podge followed by a stripe of glitter to the notebook until you’ve covered the notebook with colors of alternating glittery stripes.

    6. Add a second layer of Mod Podge and glitter to the notebook. Once you’ve covered your notebook with the stripes, brush another layer of Mod Podge over the first stripe, cover it in glitter, and then repeat this process with each stripe until you’ve covered the whole notebook with a second layer of stripes. This will make the glitter stick to the notebook even more.

    7. Add white paint to make the stripes stand out more. To emphasize the contrasting stripes, use a thin brush to add a layer of white paint around the stripes. This will make the colors "pop" more and will complete your original glittery notebook. If you’ve chosen very light colors, like yellow and baby blue, you can think about using a Gray or darker color to emphasize them instead of white.

    Method 3. T-Shirt Cover iron on transfers for t shirts

    1. This will not work with spiral notebooks- the best you can do with them is cut out two pieces- one for the back and one for the front and stick the two on. Find an old t-shirt with a fun design or logo. You will cover your notebook with this shirt, so pick something that is fun, eye-catching, and a shirt that you don’t wear any more but can’t bring yourself to throw out-just make sure that the design is small enough to fit on your notebook and not too big so that you can’t see it, and not to small so that it looks tiny on the notebook.

    2. Place the opened notebook on the T-shirt. Put it over the logo or design you’d like to put on the cover of the notebook. Open the notebook so that the pages are facing you.

    3. Mark the outline of the notebook with chalk, leaving a 2" (5 cm) border. This will help you know where to cut the t-shirt. If you cut it too close to the size of the notebook, it may end up being too small.

    4. Cut along the outline of the t-shirt. Now use scissors to cut the outline of the t-shirt. This t-shirt will cover the front and back of the notebook.

    5. Place the t-shirt cover face down. This will prepare you for sticking the t-shirt fabric onto the front of the notebook.

    6. Apply tacky glue all over the front cover of the book. Use a Popsicle stick to spread the glue all over the front cover of the notebook. Make sure to reach the edges of the notebook with the glue without covering any of the pages. You can also use a sponge brush to apply the glue. Tacky glue will work best for adhering the t-shirt to the cover of the notebook.

    7. Press the t-shirt fabric into the glue. Gently glide along the t-shirt with your hand and make sure that it sticks evenly to the glue, avoiding any bumps. The part of the shirt that you’ll be using for the back cover will remain untouched.

    8. Flip the notebook and spread glue across the back cover. Do the same thing you did to cover the front with the tacky glue.

    9. Place the remaining t-shirt fabric over the back cover. Do what you did to the front side — just take the second half of the t-shirt and press it into the back of the notebook. Then, you should wait for the notebook to dry. You can even press it between heavy books or boxes to keep it flat and to avoid any bumps that could appear under the t-shirt.

    10. Trim the fabric around the book cover. Since you left extra room when you cut the fabric of the t-shirt, you’ll have some extra fabric left over. Just cut the extra fabric with a thin and sharp pair of scissors, and touch up any parts of the t-shirt that may not have stuck to the notebook evenly with glue.

    Tips

    • You can always draw on strips of paper and glue them on later if you’re unsure of your drawing skills.
    • Sometimes just doodling is the way to go.
    • You don’t have to cut a rectangle. For a cool look you can make a star, bubble or a flower
    • All of these ways to decorate are the more-complicated version. It might just be easier to buy a pre-designed notebook or even just sharpie design on the cover of a plainer notebook.

     

    Warnings

    • If you decide to do the fabric or glitter thing, make sure it’s not too gaudy or over the top.

     

    Things You’ll Need

    Pictures and Stickers Method

    • Glue

    • Tape (any kind)

    • Markers, crayons etc.

    • Pictures from magazines, books, etc.

    • Stickers

    • Ribbon or strips of any fabric

    • Index card (any color)

    • Glitter (optional)

    • notebook

    Glitter Stripes Method
    • Two colors of glitter

    • Mod Podge

    • Sponge brush

    • White or dark paint

    • Thin paintbrush

    • notebook

    T-Shirt Cover Method

    • An old t-shirt

    • Scissors

    • Tacky Glue

    • notebook

    • chalk

    How to Remove Sticker Residue

    March 25th, 2016
    Method 1. Finger or Eraser Rubbing custom NHL decals stickers

    In some cases, it may be worthwhile trying to "ball up" the residue just using your fingers or an eraser.

    1. Check how sticky the residue is. If it’s really sticky, skip this method as you’ll just make it worse.

    2. If it’s not too sticky, run your fingers back and forth across the residue, making small balls of the adhesive as you go. Pick these balls off and discard.

    • Alternatively, use a regular eraser; the eraser dust will cling onto the residue and fall off to remove a spotless surface.
    • Don’t use your fingernails––they can easily break.

      3. Test to see if you’ve removed all the residue. If not, try again, or move onto one of the following methods.

      Method 2. Cooking Oil or Spray

      Cooking oil or spray is fairly benign and most households will have some on hand.

      1. Choose an oil. Most oils will work but olive or canola oil are good choices. Always test a little on an inconspicuous area first, just in case it’s going to stain.

      2. Pour or spray a little oil on paper towel or a cleaning rag.

      3. Lay the towel or rag across the sticky area and leave to sit for a few minutes.

      4. Lift off the rag. Scrape off the residue with your fingers (not fingernails) or a plastic scraper (a plastic knife works well).

      5. Repeat if needed. If appropriate, use a cleaner such as soapy water or a window cleaner to finish up.

      Method 3. Essential Oils

      1. Many essential oils will lift sticker residue off a number of materials, such as glass or ceramic.

      2. Be careful what you use essential oils on. In some cases, the oil may stain the surface permanently, such as unstained wood. In other cases, it may react with the material and create a stain, such as on some metals. Do a test on an inconspicuous area first. In general, essential oils work well on surfaces such as a glass, ceramic and tiles.

      3. Tip a few drops of the essential oil onto a cleaning cloth.

      4. Rub the oily part of the cloth over the residue. Rub back and forth to lift the sticky residue. Once lifted, pull the residue off the cloth and surface and discard.

      5. Repeat until the surface is no longer sticky. custom images printing If appropriate, use a cleaner such as soapy water or a window cleaner to finish up.

      Method 4. Citrus Based Proprietary Cleaners

      1. Purchase a citrus based cleaner from the hardware store. This type of cleaner goes under various names (such as Goo Gone) but the basic requirement is that it contains limonene, which cuts through the stickiness.

      • If you don’t have this product at hand, a rubbing a bruised orange or lemon peel will also work well.

        2. Follow the instructions on the packaging. Generally, it will suggest that you spray a little on the affected area, leave for a short time, then wipe off.

        • Be sure to read the instructions as to which types of surfaces it is suitable for. Some surfaces can be damaged by this type of cleaner.

          3. Allow to dry. Polish if necessary.

          Method 5. Alcohol

          1. Choose a suitable alcohol. For example, rubbing alcohol (isopropyl alcohol) or a strong, plain alcohol such as clear vodka. Avoid using any sweet or flavored alcohols, as these will introduce more stickiness from the sugar content.

          2. Spray or dab a little alcohol onto a paper towel or soft cleaning rag.

          3. Lay the moistened area of the paper or rag over the sticky stain. Let sit for a few minutes to be absorbed by the stain.

          4. Lift off the paper or rag. Remove the soaked sticky residue with your fingers or use a plastic scraper. The residue should lift off easily (use a plastic knife to scrape if necessary).

          5. Repeat as necessary.

          6. Allow to dry. Polish if necessary.

          Method 6. Masking Tape

          This method can be useful for price tags that have ripped in half when you tried to remove them. It will also help you to lift off any remaining sticky residue and any leftover price tag.

          1. Wrap a piece of masking tape around your index and middle finger. Form a snug ring, with the sticky side facing out.

          2. Press the sticky tape against the residue. Pull away. The sticky part of the tape will stick to the stickiness on the surface and pull up some of the stickiness. Repeat until you’ve lifted off as much as possible.

          • If the tape stops sticking before you are finished, use the other side or replace it with new tape.
            Method 7. Vinegar

            1. Remove old collages or sticky transfers with a vinegar wash:

            Paint over the sticky area with vinegar.

            Leave to soak for a while.

            Wash off.

            2. Soak sticky labels or residue off glass or ceramics with vinegar. This is an ideal budget-conscious solution for removing price labels and for removing anything your children have stuck on windows.

            • Saturate the sticky residue with undiluted vinegar.
            • Scrape off with a plastic knife or other similar tool.
            • Repeat as needed.
            • Let dry and polish if necessary.
              Method 8. Household Kerosene (Paraffin)

              1. Apply a little household kerosene. Note that kerosene is better known as paraffin in the UK, Southeast Asia and South Africa.

              2. Moisten a soft cloth in kerosene.

              3. Rub over the sticky residue with the moistened soft cloth.

              4. Rub until the residue lifts. Allow to dry. Polish if necessary.

              Method 9. Lighter fluid

              1. Put on disposable gloves. Place newspaper down to cover the work surface.

              2. Wet a cotton pad with lighter fluid.

              3. Wipe the sticker residue off. custom mlb stickers

              4. Use on glass or metal. Be careful with plastics; some may be dissolved or spoiled with this method.

              Method 10.Steam

              1. Put some water to boil in a kettle and wait until steam is produced. Steam works to heat up and then loosen the sticky residue left by stickers. This method works best on hard plastic, metal, and glass.

              • If you have a jar that’s not susceptible to breaking or cracking under extreme heat, you could also submerge the jar under boiling water for several minutes. The process is the same.

                2. Carefully place the sticker residue over the steam. Allow the steam to hit the residue for no more than one minute.

                3. Scratch the residue off with a knife or similar utensil. The residue should be very loose. As it cools you can remove any remaining residue with your finger.

                Method 11. Fast Food Handwipes

                Hand wipes obtained from fast food restaurants such as KFC can often remove sticker residue with ease, including removing label residue from wood, stain free.

                1. Open the pack and remove the wipe.

                2. Open the wipe. If needed, fold to suit the size of surface.

                3. Rub the surface continuously. Rub until you no longer feel any stickiness.

                4. Let it dry. Check again. If the surface still has a sticky residue, wipe the surface again

                Method 12. Credit card scraper

                1. Save old credit cards.

                2. Use these to scrape off sticky residue. Use on the kitchen counter, pans etc.

                3. Keep them handy. For example, keep one or two in your dish towel drawer and one in the car glove-box.

                Tips

                • .Other possible cleaning agents include WD-40, proprietary products, spray deodorant or perfume, (non-oily) nail varnish remover, lighter fuel, etc. Just bear in mind that the more ingredients in a product, the more likely it will be to leave a mark on absorbent surfaces such as fabric, plastic and wood.
                • .Good scrapers can be made from plastic utensils, old credit or bank cards or purpose-made plastic paint scrapers.
                • .Pour a little nail polish removed onto a paper towel, and lightly rub the affected area. It will easily remove any excess adhesive.
                • .Cover metal surface in white-out and rub off with an eraser. This should bring out the sticky residue and completely remove all evidence.
                • .If you do not have any citrus based cleaner, use lemon or orange. In particular cases, use lemon extract.
                • .Be careful if you’re scraping off a label sticker from a plastic surface, as consistent scraping can cause the plastic material to weaken.

    How to Design Your Own T Shirt

    March 18th, 2016

    Designing your own t-shirt can be a fun, creative activity, and may even bring you some money if you decide to sell your designs. Whether you intend to print the shirt yourself or send it off to a professional printer, you can still come up with the design for your shirt right at home.

    Method 1. Planning Your Design iron on transfers for t shirts

    1. Think about what your design is going to represent. Maybe you are advertising your cleaning company, your rock band, or your favorite sports team. Maybe you’re using a personal illustration. The purpose of the design will determine the design.

    • If you are advertising a company, band, sporting team, or brand, you will likely need to focus on logo. The Nike swoosh logo, for example, is a very simple but effective design. A design for a sporting team might feature the team colors or the team’s mascot. A design for your band might focus on an image of the band or a graphic that represents the band’s style or sound.
    • If you are making a t-shirt to showcase a personal illustration or drawing, you will need to focus on how it will look on a t-shirt. Think about how original the illustration is and how the colors are working in the illustration.
    • Consider using a photo in your design. Use your own photo, or a photo from the Internet, which are considered public-domain. You can also buy a stock image.

    2. Pick a color scheme. When designing a t-shirt, its important to think about color contrast. This means how certain ink colors in the design will appear against a lighter colored shirt or a darker colored shirt. Certain ink colors look more vibrant on a lighter or darker shirt on the computer screen than they actually do when printed.

    • When using lighter shirts, avoid pastel colors like yellow, light blue, or light pink. These colors will be visible on the shirts but may not be legible at a distance. And if you are designing a shirt with a logo, you want to make sure that logo is legible from far away!
    • If you decide to use pastel colors, add an outline of a darker color to the lighter color to highlight the text and make it easier to read.
    • Darker colored shirts look good with lighter ink colors, such as pastels. But be careful when using darker ink colors on darker colored shirts like cardinal (dark blue), maroon, or forest green. These colors may look great on the computer or in a drawing, but when they print, the shirt color sometimes distorts the ink color. As a result, they can appear more brown or dull.
    • If you decide to use Adobe Illustrator to create your design iron on transfers for t shirts, the Global Colours settings can help immensely with color schemes.

    3. Add dimension to the design. Once you’ve added your colors to the design, it may look good but still a bit flat or one dimensional. To create more depth to a certain area of the design, add a color that is the shade of the color beneath it. This will brighten up the design and give it some dimension.

    • If you plan to use software with a high capacity for manipulation (such as Adobe Photoshop, InDesign, Gimp, Adobe Illustrator, or Paint Shop Pro), you can use a standard image and radically transform it to fit your needs.
    • Creating a vector outline on Inkscape is an especially effective way to resize a photo if necessary.

    4. Balance your design. This means combining all the parts or elements to form a whole. How you do this depends on the composition of your design. Maybe your design has a lot of smaller elements, like stars, plants or animals. Or may it is one large design with one main figure or image.

    • Think about how you can make the design look cohesive, so that all the parts or elements fit well together. A balanced image will immediately draw the eye in rather than away from an image.

    5. Determine the placement of the design on the t-shirt heat transfer for t shirts. Would your design work better as a centered image, an image on the top left of the t-shirt or as a wraparound image?

    • If you are designing a t shirt for a brand or company, a simple design in the center of the shirt may be the most effective.
    • Don’t forget you can also use the back of the t-shirt to include a branding slogan (“Just Do It”). Or a song lyric from a song by the band you are designing the shirt for.

    6. Complete a final mock up of the design. It’s best to sketch your ideas out before putting them on your t-shirt. Try out several different designs and color combinations. Keep in mind color contrast and dimension. Make sure the image is balanced and cohesive.

    • When in doubt, get a second opinion. Ask friends, family, or coworkers what design and color scheme they like best.
    Method 2. Making a Digital Image of the Design custom images printing

    1. Use Adobe Photoshop to touch up your paper sketches. If your paper sketches are not high quality or drawn with clear lines, this option may not work. If your sketch is high quality:

    • Scan the sketches to your computer. Then, retouch them in Photoshop.
    • Clean up the lines. Play with the filters, colors, brightness, contrast, saturation, or any other effects at your disposal.
    • Add lines, flourishes, splatter effects, and other embellishments that might make the design more dynamic and balanced (where appropriate).
    • Make sure that the entire layout is internally consistent by keeping proportions reasonable, styles consistent, and colors cohesive.

      2. Use computer software to create the design. If you aren’t happy with the quality of your paper sketches, use computer software to draw line art on Photoshop.

      • If you have a computer drawing tablet, you can color and draw straight onto Photoshop or a similar program.

    3. Add text to the design, if desire. Look for a font that complements your overall design, rather than overwhelm it. The font should work with the image(s) in your design to create a balanced design.

    • Think about the fonts on some of the more well known logos or designs. The font should relate back to the company or brand’s overall style. Nike’s Just Do It’s slogan, for example, is in a bold and simple font, just like their bold and simple swoosh logo. In contrast, the font used for a sports team or a garage rock band may be more elaborate or ornate.
    • Make sure any filters you are using on the design are also applied to the font. If you are working with layers on Photoshop, you will need to drag your font layers below the photo effects layers.
    • Use free fonts from an online site like defont.com. You can also access free brush designs from brusheezy.com.
    • Look at how to add fonts to your PC, Illustrator, or Photoshop if necessary.
    • If you’re feeling adventurous with design, you can make your own.

    4. Create a prototype. The easiest way to do this is to print the design and iron it onto a plain shirt. However, if you want to test the quality of your design, you can hire a printing company to create a professional prototype.

    5. Produce the shirt(s). For a small-scale operation, you can continue ironing on the design. #*If you’d like to make shirts at a larger scale, however, you can pay a printing company custom sublimation printing to make them for you.

    Method 3. Screen-Printing Your Design

    Gather your supplies. To screen-print your design at home, you will need:

    • A plain t-shirt
    • 50 ml bottle of degreaser (available at your local art store)
    • 1 liter cold water
    • A large brush
    • 500 ml of emulsion
    • A small bottle of sensitizer
    • A bottle of screen printing ink
    • A squeegee or a coating tray
    • A small wooden stick
    • A hair dryer
    • A transparency
    • A printing screen
    • You can purchase a printing screen at your local art store. Or make your own by buying a mesh screen and a canvas stretcher frame. Stretch the mesh across the frame and staple the edges down so that the mesh is taut. For standard designs on a light shirt, a 110-195 mesh works best. For fine designs with multiple colors, use a 156-230 mesh.

    2. Prepare the printing screen. Mix the degreaser and the cold water together. Place the brush in the mixture and then brush the mixture on to the screen.

    • Make sure you brush both sides of the screen. You just want to give the screen a light brush so don’t worry about putting too much of the mixture on the screen.
    • Let the screen dry.

    3. Mix the emulsion and the sensitizer together. Take 20 ml of water and pour it into the bottle of sensitizer. Mix the sensitizer well by shaking for a about a minute.

    • Add the sensitizer into the emulsion.
    • Use the small wooden stick to mix the sensitizer and the emulsion together.
    • The color of the emulsion should change from blue to green. There should also be small bubbles forming in the emulsion.
    • Place the lid loosely back on the emulsion and place it in a dark area or room for an hour. After an hour, check that all the small bubbles in the emulsion have disappeared.
    • If they do not disappear after an hour, leave the emulsion to sit for another hour until the bubbles are gone.

    4. Apply the emulsion on the screen. In a very dim room or with a low red light, drip a line of photo emulsion across the screen and use a squeegee to spread it around.

    • The emulsion will leak through the screen, so be sure to squeegee both sides of the screen.
    • You can also use a coating tray to apply the emulsion to the screen. Do this by placing the screen on a clean towel and tilting it away from you slightly. Place the coating tray at the bottom of the screen and carefully pour the emulsion on the screen as you move the tray up the screen.
    • Leave the emulsion to dry in a completely black room for about twenty minutes. Use a fan to help the screen dry.

    5. Place the transparency down backward on the screen. Now you’re ready to burn your image into the emulsion. Do this by placing the screen flat, placing the transparency down backward, and placing a piece of glass over the transparency to ensure that it doesn’t move.

    6. Burn the design into the emulsion. A 500-watt lightbulb will burn the transparency image into the emulsion in roughly fifteen minutes.

    • The exact times for this process depend on the light and emulsion you use.
    • Specific directions for the light needed should be on the packaging of the purchased emulsion.

    7. Rinse the screen. Let the screen soak in a thin layer of water for about two minutes. Then rinse any excess emulsion off with a hose or in the shower.

    8. Place waterproof tape around the edges of the underside of the screen. The flat side of the screen will go facedown on the shirt, and the side with the frame is where you will use the ink. #*To make sure no ink ends up leaking around the frame, use waterproof tape to secure around the edges where the screen stretches over the frame.

    9. Lay your t-shirt on a flat surface. Make sure there are no wrinkles. Place the screen on top of the t-shirt, where you would like your design to be. Place the screen on top, making sure that the screen and design are aligned.

    • Clip your shirt down to a firm piece of cardboard. Doing this will ensure your t-shirt remains flat and unwrinkled. It will also make it easier to move your t-shirt to a safe spot later to dry.
    • If possible, have a friend hold the screen down tight while you spread the ink.

    10. Spread a tablespoon of screen printing ink on the top of the screen. Using your squeegee, coat the screen by spreading the line of ink from top to bottom.

    • The mesh is actually quite thick, so this step is more of a primer.
    • Use very light pressure so you don’t push any ink through the screen.

    11. Squeegee the screen. With the screen flooded, you’re ready to transfer the design to the shirt.

    • Use the squeegee at a 45° angle in both hands to evenly distribute the pressure. If possible, ask a friend to hold the screen in place.
    • Drag the ink back up across the flooded screen over the design.

    12. Cure the ink. Using a hairdryer, apply even heat to the design for several minutes.

    • Cure the ink before using the next screen to add additional layers of the graphic in different colors.
    • If you use the proper screen-printing technique and cure it, your t-shirt will be washing machine safe.

    13. Wash your screen once you are done making your shirts. Use cold water and scrub it with a sponge to get the ink out. Let the screen air dry.

     

    Method 4. Stenciling Your Design

    1. Gather your materials. To stencil your design onto a t-shirt, you will need:

    • A black and white print out of your design. Its important to use a black and white printout of your design so it will be easy to trace.
    • A piece of contact paper, or a transparency
    • A craft knife, or exacto knife
    • A plain t-shirt
    • A piece of cardboard big enough to cover the front area of the shirt

      2. Tape the design to a piece of contact paper. Contact paper is clear paper used for covering books. It has a normal side and a sticky side that peels off. You want to tape your paper to the peeling side so that the design is visible through the front of the contact paper—the non-sticky side.

      • You can also use a piece of transparency or clear paper. Attach it to the printout of your design with tape.

    3. Use a sharp craft knife to cut out the black parts of the design. Lay the attached papers on a flat surface, like a table.

    • Trace the lines with the craft knife or an exacto knife. Keep in mind the black parts you cut out are the parts of the design that will be filled with paint.

    4. Peel the sticky side off the contact paper. Remove the normal paper with the design from the contact paper as well. Place the sticky stencil onto the t-shirt, making sure it is straight and not wrinkled.

    • If you are using a transparency or clear paper instead of contact paper, attach the transparency to the shirt with tape.

    5. Place a piece of cardboard inside the t-shirt. Doing this separates the front and back so the ink doesn’t bleed through to the other side.

    6. Use a sponge brush to paint on the fabric paint. Only put paint on the spots that have been cut out of the contact paper—the spots that will be painted in dark on the t-shirt.

    • Let the paint dry. Test the paint by gently touching the painted spots. If paint comes away on your finger, it is not fully dry.

    7. Peel the contact paper off of the t-shirt when the paint is dry. You will now have a stenciled on t-shirt.

    • You can use the stencil to make another shirt if you want more than one stenciled t-shirt.
    Method 5. Bleach Painting Your Design

    1. Use bleach safely. Bleach painting is a fun, easy, and inexpensive way to create a design on a t-shirt, especially text based designs. But, remember bleach is toxic, so keep it out of reach of children.

    Always protect your eyes, clothing, and any open cuts from coming into contact with bleach.

    • If you have sensitive skin, you should wear thin kitchen gloves while bleach painting.

    2. Gather your supplies. You will need:

    • Fabric safe household bleach
    • A synthetic bristle paint brush (go for an inexpensive one, as you’ll just be bleaching it anyway!)
    • A glass or ceramic bowl
    • A white towel or rag
    • White chalk
    • A piece of cardboard
    • A dark colored cotton blend shirt
    • You can try this method on a lighter colored shirt, but the bleach painting will show up better on darker colors.

    3. Place your shirt on a flat surface. Then, slide the piece of cardboard inside your shirt. It will act as an even surface as you write your design. It will also stop the bleach from bleeding through the back of your shirt.

    4. Use the white chalk to sketch out your design on the shirt. This could be your favorite saying (“Bazinga!” “Reach for the Stars”), the name of your band, or the logo of your brand.

    • Don’t worry if you need the smudge out the chalk lines and re-sketch the design. The chalk lines will wash out once you’ve completed the bleach painting.

    5. Fold the sides of the shirt under the cardboard. Secure the shirt to the cardboard with elastics or small clips. This will keep the cardboard from slipping while you bleach paint.

    6. Prepare the bleach. Pour a few cups of the bleach into the glass or ceramic bowl. Use a towel to wipe up any drips. You don’t want any drops of bleach to end up on your clothing.

    7. Dip your brush into the bleach. Drag it on the edge of the bowl to eliminate any dripping.

    8. Use steady strokes to trace the chalk lines of your design. For an even bleach line, reload your brush every two inches. The fabric will quickly soak up the liquid so work quickly, but with a steady hand.

    9. Finish tracing your design. Then, take a break to allow the bleach to react with the fabric of the shirt.

    • Look over the shirt. Are there any uneven spots or light areas? If so, go back in with your bleach filled brush and even out the design.

    10. Let the shirt sit in the sun for at least an hour. This will allow the bleach to process and lighten.

    • Depending on the cotton content of your shirt, the color of your design will range from dark red, to orange, to pink, or even white.

    11. Rinse and hand wash your shirt. Hang it to dry. Admire your new permanent bleach design.

    • Wash the shirt with like colors. The chalk lines should wash out, leaving only the bleach design.

    Tips

    • Keep in mind digital printing is the simplest way to make a lot of t-shirts at once. Screen printing, stenciling, and bleach painting at home are good methods if you want to make a few t-shirts.
    • Once you have a digital image of your design, you can always have a professional screen-printing company do all of the print work for you.
    • When using an image from the internet, print it out on a transfer paper for better quality.
    • If you’re planning to sell T Shirts make sure the art/images aren’t copyrighted and you are allowed to sell them. If you use an image that belongs to someone else, you may get in big trouble ruining the reputation of your shop and it may lead to getting sued.

    Che Guevara,a symbol of freedom and ideal

    May 21st, 2015

    ~E2ND8R0XKCYX4`T2}S{]TI

    "CHe" is a symbol of freedom and ideal, A culture symbol of chasing rebellion and sincere. The revolutionary youth idol in the world, has become a spiritual symbol.

    `~VIG`4Y0XM1{[T3CN4LAQW[4]

    CHE in your T shirt reminds you fighting for your future.

    YOU CAN FIND THE HEAT TRANSFER SUPPLIER TO MAKE IT

    WHAT ANIMALS YOU LIKE IN THE ZOO

    May 20th, 2015

     

    LET THE CUTE ANIMALS LIVE IN YOU T SHIRT

    FUNNY ANIMALS T SHIRT

    RUN8P61(KHRD[24(8`16TBCBNRTB0MQW}KO7PN~2YVX`O5QI$`}8)2H~DYI@]Y[C00J_6{%59@E%L@S}2K)$CWIA35)E89LEF757`_SVD4)U_V~`DCNG{D7L@VBGAH$A3K6P688[QS [G5)TBDPH@}D@`L6M03(PS6

    IF YOU LIKE ,ASK THE HEAT TRANSFER SUPPLIER TO MAKE IT

    HOW DIY T SHIRT LOGO

    May 13th, 2015

    How design your t-shirt  and Printing
    We also do custom t shirt design and printing for special events, sports teams, uniforms, family reunions and fundraisers.we  can also design what you want t shirt logo,please click here
    Customer Care
    Our goal is to design high quality t shirts and provide excellent customer service. Thanks for your feedback. We always leave positive feedback for our customers.
    t-shirt-project-x-black-flowers-pu-armel.jpg

    100% cotton t-shirt
    The art work is printed on 100% heavyweight (6.1 0z) preshrunk cotton.

    Digital Printing
    Printed at 1200 dpi with the new Brother state of the art Direct to Garment printer for vivid photorealistic colors.

    Washing/ Drying
    Machine wash warm, inside out, with like colors. Tumble dry medium. Do not iron image. Do not dry clean.

    Packaging
    The T-shirt will be shipped in a padded tear proof envelop.
    This has proved to provide maximum protection during shipping.

    Payment
    We prefer payment through Paypal.
    Shipping
    We ship within 1 business day of order.

    What’re glow in the dark water transfer paper for temporary tattoos

    February 26th, 2015

    Nowaday more and more people are not font of real tattoos that are meant to stick on skins forever. So temporary tattos are coming into being, especially glow in the dark water transfers for temporary tatoos. So what can glow in the dark water transfers for temporary tatoos do? Today we take a scan.

    tatoo heat transfers

    Features of glow in the dark water transfers for temporary tatoos

    1. Non-toxic&healthy

    2. easy to apply and remove with no pain.

    3. Beautify your body

    4. Kids temporary tattoos

    5. Water proof .

    6. Ideal for body decoration and promotion.

    How to apply glow in the dark water transfers for temporary tatoos?

    1. Clean and dry the skin completely

    2. Remove the transparent film

    3. Place “TATTOO” face down on the skin

    4. Rub and wet the “TATTOO” completely with water

    5. Peel the corner of the “TATTOO” gently to check if it is transferred.

    6. Your “TATTOO” can last for several days if transferred carefully

    How to remove glow in the dark water transfers for temporary tatoos?

    1. Rub with cold cream or baby oil

    2. Alcohol will remove the “TATTOO” instantly.

    Now you will have any tatoos any time.

    When you are interested in glow in the dark tatoos? are you also font of glow in the dark shirt heat transfer logos or images? Visit logoheattransfer.com, you will find that you can create your own t shirt fasion easily and nicely.